They are making a number of great pointers on Installing A Bathtub in general in this post down below.
Setting up a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a new one is also a reasonably hard task. If the old bathtub is easily easily accessible, the task can move easily; if you need to open up a wall surface to remove the old tub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's abilities, although you will need an assistant to leave the old tub and also set in the brand-new one. Make sure you have qualified yourself for the task and are comfortable trying it. Rather than employing a professional to take over a halfway-completed job, it is better to take into consideration employing one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This post will help you mount a brand-new bath tub in your shower room if you have actually already acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipelines.
Your devices and also product list should comprise the following:
Planning for the Installation
First of all, the supporting framework provided with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the limited access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the needed position. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub until the level reviews level.
To install taps, fit the bottom of the furthest versatile faucet port to the suitable supply pipe by making a compression join; after that do the same for the various other faucet.
Turn on the water system and inspect all joints as well as new pipework for leakages as well as tighten them if needed. Fill up the bath tub as well as additionally inspect the overflow outlet and the typical outlet for leakages.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub must wait until the bath tub has been made use of at the very least when as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Secure the faucet in place with the supplier given backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous type ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, bring about issues with dampness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and also cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealer can split fairly very early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very curious about How to Install a Bathtub Yourself and I'm hoping you appreciated the article. Remember to take the time to distribute this entry if you enjoyed it. Thank you for your time. Visit us again soon.
Need fast action?